Logotipo Texsa, S.A.

TECSOUND® SY

TECSOUND® SY is a high density polymer-based, asphalt-free, synthetic soundproofing membrane, that offers good acoustic insulation in different building elements. It is equipped with a self-adhesive layer, to allow its direct application on the majority of building surfaces

Technical documentation

  • Logo Facebook
  • Logo Twitter
  • Logo Linkedin
  • Advantages
  • Application
  • Installation
  • Storage
  • Regulations
• High acoustic insulation, combined with soft, flexible elements.
• Flexible.
• Great elongation capacity
• Easy handling and adaptable to uneven surfaces.
• Good bonding to most of the types of surfaces.
• Acts as a vapour control layer
• Cold- and heat-resistance.
• Excellent ageing resistance.
• Rotproof.
• Soundproofing against airborne noise in vertical walls with low surface density (lightweight partition walls or boards made of different materials).
• Soundproofing against airborne noise in ceilings and lightweight roofs.
• Reduction of impact noise level in all types of floors, sandwiched between floor slabs and loose-laid flooring.
• Damping of impact noise caused by atmospheric agents on metal decks.
• Combined with sound-absorbent materials, it offers products with high acoustic performance.
• Its applications in the industrial field cover from the soundproofing of booths to the acoustic insulation of machine-rooms, gutter pipes, sound damping of metal sheets, etc.
Substrate: TECSOUND SY lends itself to all types of normal building substrates (renderings, gypsum board, metal, DM, plastic materials). The substrate must be even, smooth, clean and dry. It must also be free from elements that could damage the membrane. If the rendering is old, its condition must be checked to avoid adherence problems of the TECSOUND sheet to the rendering.
Installation of the membrane: Remove the protective silicone release paper, and align the membrane on the substrate, exerting pressure over the whole membrane to ensure good bonding. If the length of product is very large, or it is applied in rolls, remove the protective release paper progressively to aid installation.
Installation of the membrane on metal decks: The membrane must be applied in such a way that the length of the roll is perpendicular to the direction of the fretwork. The membrane must be made to follow the profile of the metal support at all times, ensuring that there is no formation of air pockets. The thermal insulation boards are then installed, mechanically fastened.
Laps: Overlap 5 cm both vertically and horizontally. Care must be taken to always seal the laps correctly, as small openings can reduce the level of acoustic insulation required.
Yield: 1 m2 of membrane covers approximately 0.95 m2 of surface area, including overlaps.
TECSOUND® SY35
Roll:8,05 x 1.22 m.
Pallet:24 rolls (235.7 m2)
TECSOUND® SY50
Roll:6.05 x 1.22 m.
Pallet:24 rolls (177.14 m2)
TECSOUND® SY70
Roll:5.00 x 1.22 m.
Pallet:24 rolls (147.86 m2)
TECSOUND® SY100
Roll:4.00 x 1.20 m.
Pallet:1.00 x 1.20 m. sheets
21 rolls (100.8 m2)
75 sheets (90 m2)
· In accordance with the following norms: CTE-DB-HR, EN ISO 140-1, EN ISO 140-3, EN ISO 140-6, EN ISO 140-8, EN 20140-2 and EN ISO 717/1/2.
· Quality System in accordance with ISO:9001

Related Products

 

DATA PROTECTION

 

In cases where the user must provide data of a personal nature to TEXSA SYSTEMS SLU to use any of the Web services, the former will be expressly informed each time of the existence of an automated data base, the aim of same, those receiving the information and identity and address of the person responsible for data treatment, all with the aim of complying with that stipulated in Organic Law 15/1999 of 13th December, for the Protection of Data of a Personal Nature. To this effect, TEXSA SYSTEMS SLU shall reserve confidentiality of the data obtained and the users can exercise all rights to access, amendment, cancellation and any others referred to in aforementioned Organic Law 15/1999.

TEXSA SYSTEMS SLU has adopted all the necessary measures of a technical and organisational nature, to guarantee the security of the data of a personal nature, with the aim of preventing their alteration, loss, treatment or unauthorised access, in accordance with the requirements and conditions called for by Royal Decree 994/1999 of 11th June, in which the Regulation of safety measures of automated files containing data of a personal nature, is passed, notwithstanding the user's acceptance and knowledge that to date totally impregnable safety measures do not exist.

In case of doubt or the need to extend the information covering any of the above items, please do not hesitate to contact TEXSA SYSTEMS SLU.

 

TEXSA SYSTEMS SLU.
C/Ferro Nº7,
Polígono Industrial Can Pelegrí,
Castellbisbal
08755, Barcelona - Spain
NIF B66067687

Tel. (+34) 93 635 14 00
Fax (+34) 93 635 14 80

Email:  lo...@texsa.com